-
1 valve sub-base
-
2 Ventilplatte
-
3 узел (агрегат, блок)
assembly, unit
ряд деталей или подузлов, соединенных вместе для выполнения определенной функции. — а number of parts or subassemblies or any combination thereof joined together to perform a specific function.
- (единица скорости) морская миля (1852 м в час) — knot (к, kt) а nautical mile per hour.
- (изделие) количество деталей на изделие (графа таблицы). — assembly (assy) units per assy.
- (составная часть агрегата, блока, установки) — sub-assembly, subassembly
две или более деталей, о6разующих часть агрегата (сборки) или блока и заменяемых как одно целое, но включающее деталь (детали), подлежащие индивидуальной замене. — two оr more parts which form а portion of an assembly or а unit replaceable as а whole, but having а part or parts which are individually replaceable.
- а (обозначение на чертеже) — detail а
- (часть) агрегата — sub-assembly, assembly
the distinction between an assembly and sub-assembly is not always exact.
- баков (масляных) (блок) — oil tank assembly
два отдельных бака установлены в одном узле. — two separate tanks are housed within the tank assembly.
-, гиростабилизированный, на карданном подвесе — gyro stabilized gimbal assembly
- гироскопа — gyro assembly
- дозирующей иглы (топлива) — throttle valve assembly
-, законченный (конструктивно) — definite-purpose assembly
-, качающий — pumping unit
насос имеет два отдельных качающих узла, состоящих из блока плунжеров, вращающихся no скошенной пяте. — the pump has two independent pumping units consisting of pfunger rotating assembly working against a variable angle swash plate.
- клапана (поддержания) постоянного (пропорционального) перепада давлений (насоса-регулятора) — proportioning valve unit
- компрессора (двиг.) — compressor section
- компрессора (подраздел 72-30) — compressor section
- контроля (блока питания) — monitoring device
работа основана на сравнении контролируемых напряжений с эталонными.
- крепления — attach(ment) fitting
- крепления груза (на борту ла) — cargo tie-down fitting
- крепления двигателя — engine mounting attachment
узлы крепления двигателя и конструкция, несущая эти узлы, должны выдерживать указанные нагрузки без разрушения, поломки или остаточной деформации. — the engine mounting attachments and related structure must be able to withstand the specified loads without failure, malfunction, or permanent deformation.
- крепления закрылка — flap attach(ment) fitting
- крепления крыла — wing attachment fitting
узлы служат для крепления крыла к фюзеляжу. — the fittings on the wing used to attach the wing to the fuselage.
- крепления оси колес (к стойке шасси) — wheel axle attachment fitting
- крепления руля высоты (или направления) — elevator (or rudder) hinge /attach/ fitting
- крепления опоры шасси, (передний, задний) — (forward, aft) landing gear strut attachment fitting
- крепления страховочных строп (или троса) — safety harness (or line) attach(ment) point /receptacle/
- крепления, шарнирный — hinge fitting
- крепления элерона — aileron hinge /attach/ fitting
-, магнито-индукционный (тахометра) — magnetic-drag assembly
-, манометрический — pressure capsule assembly
-, манометрический (трубка бурдона) — bourdon tube assembly
-, мембранный — (pressure) capsule assembly
- мембранный (указателя скорости) — airspeed capsule
- навески (общий термин) — attach(ment) fitting
узлы, служащие для крепления стабилизатора, руля высоты, триммеров, обтекателей. — the fittings on the stabilizers used for attachment of stabilizers, elevators, rudder tabs, fillets/fairings.
- навески (шарнирный) (рис. 10) — hinge fitting
- навески закрылка — flap attach(ment) fitting
- навески руля высоты (направления или элерона) — elevator (rudder or aileron) hinge fitting
- навески руля направления, верхний (нижний) — rudder top (bottom) hinge fitting
- навески руля высоты (или элерона), внешний — elevator (or aileron) outboard hinge fitting
- навески руля высоты (или элерона), внутренний (корневой) — elevator (or aileron) inboard hinge fitting
- навески руля (или элерона), средний — elevator (оr aileron) center hinge fitting
- навески триммера — trim tab hinge fitting
- навески шасси — landing gear (shock strut) attachment fitting
- насоса, управляющий — pump controlling section
- ограничения (раскрутки) оборотов (насоса-регулятора) — overspeed limiting control
- основной дозирующей иглы (командно-топливного агрегата или насоса-регулятора) — throttle valve (sub-) assembly (of fuel flow control unit)
- плунжерный качающий (наcoca) — plunger rotating assembly
- поворота крыла (в горизонтальной плоскости) — wing pivot (assembly)
- подвески вооружения на пилоне — weapon-pylon base
- подвески двигателя — engine mount
каркас, поддерживающий двигатель и крепящий его к мотогондоле или пилону. — the framework which supports an engine and attach it to the nacelle or pylon.
-, поршневой (узел цилиндров тормоза колеса) — cylinder assembly
- приемника-процессора, электронный — receiver-processor electronic assembly
- прямой (завязки шнуров, тросов) — square knot
- разъема коммуникаций, унифицированный (уурк) — combined services connector
- растормаживания (тормоза колеса) — (brake) retraction mechanism
для возвращения (после снятия давления в тормозе) нажимного диска в исходное положение, т.е. для растормаживания колеса. — the brake has automatic adjustment, integral with the retraction mechanism built into each piston, movement of the piston compresses the retraction springs.
-, регулируемой подпитки (топливом гтд) — variable enrichment unit
-, рифовый (завязки строп) — reef knot
-, рычажно-кулачковый (дозир. иглы) — throttle valve cam and lever assembly
-, силовой (блок цилиндров тормоза колеса) — cylinder assembly
-, скоростной (указателя скорости) — airspeed capsule
-, страховочный (для крепления страховочного троса или ремня) — safety rоре (or belt) attach fitting /point/
-, стыковой (стыковочный) (рис. 16) — attachment fitting
-, такелажный (точка подъема) (рис. 10) — hoist point
- такелажный (деталь) — hoist fitting
- турбины — turbine section
состоит из ступеней высок. и низк. давлений, приводящих во вращение соответствующие компрессоры. — consists of hp and lp stages, each driving their own compressors through concentric shafts.
- турбины (подраздел 72 - 50) — turbine section
- турбины и реактивного сопла — turbine and exhaust section /unit/
- (-) удавка (завязки шнуров, тросов) — running knot, slip knot
- управления и блокировки реверса тяги (насоса-регулятора) — thrust reverser control and interlocking unit
- управления приемистостью (топливного насоса-регулятора) — acceleration control (unit)
-, функционально законченный — definite-purpose assembly
- цилиндров (блок тормоза колеса) — cylinder assembly
-, швартовочный (груза на борту ла) — tie-down fitting
-, швартовочный (швартовый, ла) (рис. 150) — mooring fitting
- штока амортизатора (шасси), нижний — shock strut piston lower fitting
- электро-гидравлический /электро-гидромеханический / (гидроусилителя) — electro-hydraulic unit
командные эл. сигналы подаются в электрогидравлический узел гидроусилителя (бустера), в котором они преобразуются в механическое перемещение соответствующих золотников. — autocontrol demands are signalled electrically to the electrohydraulic unit on each surface drive (hydraulic booster) which converts them to mechanical movements (of corresponding slide valves)
завязывать у. — tie a knot
развязывать у. — loose a knot
определять дефект в у. (точнo устанавливать отказавший узел) — isolate the trouble into sub-assemblyРусско-английский сборник авиационно-технических терминов > узел (агрегат, блок)
-
4 unit
1) сборочная единица; узел; блок2) установка; агрегат3) единица, единица измерения || единичный; удельный4) часть; секция || секционный•as a unit — 1) в сборе 2) как единая сборочная единица; как единый узел
unit under test — 1) объект контроля 2) объект диагностирования, объект технического диагностирования
- AC unit- actuating unit
- adapter plate unit
- adaptive control unit
- address and data interface unit
- address unit
- adjusting unit
- air-aspirating unit
- answer-back unit
- arithmetic unit
- arithmetic/logic unit
- arithmetical unit
- ASC unit
- assembly unit of N-order
- assembly unit
- audio response unit
- autoloading unit
- automatic calling unit
- auxiliary data translator unit
- availability control unit
- axis unit
- axis-processing unit
- balancer unit
- banking unit
- bar feed unit
- base assembly unit
- base unit
- basic information unit
- basic length unit
- basic logic unit
- batch control unit
- bearing unit
- behind-the-tape reader unit
- belt shuttle unit
- belt-driven shuttle unit
- bench-testing unit
- blemished unit
- bolt-on unit
- booster unit
- boring spindle unit
- boring unit
- boring-and-milling unit
- brake unit
- broach retriever unit
- broach-handling unit
- broken tool sensing unit
- buffer unit
- building-block machining unit
- bulk transfer unit
- business unit
- card punching unit
- carousel loading unit
- carousel unit
- carrier unit
- cartridge unit
- cellular unit
- center unit for machine frame
- central processing unit
- central processor unit
- chain storage unit
- changer unit
- changing unit
- check unit
- chiller unit
- chip disposal unit
- clamping unit
- claw unit
- CNC machining unit
- CNC standard unit
- CNC unit
- coating application unit
- coating removal unit
- coherent unit
- column unit
- combination valve unit
- command unit
- communications central processing unit
- complementary unit
- computerized numerical control unit
- condensing unit
- cone variable-speed friction drive unit
- console unit
- constant coefficient unit
- constant delay unit
- construction unit
- control unit
- controlling unit
- conveying unit
- conveyor unit
- coolant management unit
- coolant recovery unit
- coolant unit
- cooler unit
- cooling unit
- coordinate preprogramming unit
- copying unit
- correction unit
- cover unit
- CPC handling unit
- cross tapping unit
- cross-slide unit
- cutoff unit
- cutting unit
- D unit
- damping unit
- data preparation unit
- data transmission control unit
- deep hole boring unit
- delay unit
- derived unit
- detecting unit
- detection unit
- developing unit
- digital display unit
- digital readout unit
- digital unit
- dimension readout unit
- diode array unit
- disk-type variable-speed friction drive unit
- displacement unit
- display unit
- distance-keeping unit
- double-acting unit
- double-notching unit
- double-pump and combination unit
- double-pump unit
- double-reduction gear unit
- double-reduction right-angle reduction gear unit
- double-reduction twin gear unit
- double-reduction twin unit
- double-reduction wormgear unit
- double-spindle unit
- down-hole internal deburrer unit
- dresser unit
- dressing unit
- drill unit
- drilling and milling unit
- drilling spindle unit
- drilling unit
- drilling/tapping unit
- drive unit
- drive/feed unit
- DRO unit
- dual work pallet shuttle unit
- dual-head laser beam unit
- dust-collecting unit
- dust-removing unit
- dynamic unit
- EDM unit
- electrical machining units
- electromagnetic unit
- electron-beam unit
- entry level dedicated unit
- environmental compensation unit
- exchanger unit
- fabricated unit
- facing unit
- fan coil unit
- feed box unit
- feed change unit
- feed drive cartridge unit
- feed unit
- feedback unit
- feed-in boring unit
- feed-out boring unit
- fetch-and-carry unit
- filtration unit
- fine boring unit
- flexible spindle units
- flexible tray unit
- floor unit
- focusing unit
- free-standing unit
- free-wheel unit
- free-wheeling unit
- frontal variable-speed friction drive unit
- functional unit
- fundamental unit
- gage control unit
- gage indicating unit
- gage unit
- gaging unit
- gas turbine starter auxiliary power unit
- gear unit
- gearbox unit
- gear-reversing unit
- grasping unit
- grinding spindle unit
- gripper unit
- guide unit
- handling unit
- hardware/software add-on unit
- harmonic drive unit
- head unit
- headstock-type workpiece holding unit
- hoisting unit
- horizontal power unit
- horizontal way unit
- hydraulic clamping unit
- hydraulic feed unit
- hydraulic power unit
- hydraulic testing unit
- hydraulic unit
- hydrostatic bearing unit
- ICAM manufacturing unit
- ICAM unit
- icon-driven control unit
- indexer/fourth axis unit
- indexing head unit
- indexing platen unit
- indexing table unit
- indexing unit
- in-die tapping unit
- information retrieval unit
- information unit
- input batch control unit
- input unit
- input-output unit
- in-system unit
- integral unit
- interface unit
- intermediate storage unit
- interpolating unit
- inverting unit
- keyboard unit
- knee-type unit
- lapping and superfinishing unit
- laser beam composition unit
- laser beam unit
- laser processing unit
- laser unit
- laser-calibration unit
- laser-source unit
- lead screw tap unit
- lexical unit
- lift unit
- lift-and-carry unit
- light unit
- linear ball bearing unit
- linear drive unit
- linear screw unit
- linear slide roller bearing unit
- linear unit
- live storage unit
- load/unload unit
- loading unit
- loading-and-unloading unit
- logic unit
- logical unit
- lubricating pump unit
- machine control unit
- machine tool control unit
- machine tooling unit
- machine unit
- machine-dedicated unit
- machining center unit
- machining head unit
- machining unit
- magnetic pickup unit
- magnetic tape unit
- manned flexible unit
- marking unit
- master unit
- material-handling unit
- MDI unit
- measurement unit
- measuring unit
- memory unit
- message display unit
- microdispensing unit
- microprocessor correction unit
- microprocessor NC unit
- microprocessor unit
- microprocessor-based unit
- microprocessor-type NC unit
- middle-level 3-D representation unit
- milling spindle unit
- minicomputer control unit
- miniload AS/RS unit
- mist coolant unit
- miter saw unit
- mobile unit
- mobile work storage unit
- modular cell unit
- modular loading unit
- modular unit
- motor unit
- motor-reduction unit
- multichannel analyzer unit
- multidrill unit
- multiple screw-driving unit
- multiple-power path gear unit
- multiple-reduction gear unit
- multiple-reduction unit
- multiple-spindle torque unit
- multipurpose machining unit
- multispindle boring unit
- multitap unit
- NC data creation unit
- NC unit
- nested gear unit
- notching unit
- nutating unit
- off-machine unit
- off-system unit
- oil coalescer unit
- oil-filled feed unit
- one stage gear unit
- one stage unit
- on-machine unit
- operation unit
- operational unit
- operator-friendly program unit
- orientation transfer unit
- output batch control unit
- output unit
- overhead gantry unit
- overhead spindle unit
- pack unit
- pallet change unit
- pallet exchange unit
- pallet shuttle unit
- pallet-pool unit
- parallel-shaft reduction gear unit
- PC expansion board unit
- PC-based CAD unit
- pendant control unit
- pendant pushbutton control unit
- pendant unit
- peripheral control unit
- peripheral processing unit
- photo-eye tracing unit
- pick-and-place unit
- pickup unit
- piece-holding unit
- pilot unit
- placement unit
- planetary gear unit
- planetary reduction gearing unit
- plant unit
- plasma-arc unit
- plasmarc unit
- platen unit
- PLC unit
- plugboard input unit
- plugboard unit
- plug-in unit
- pneumatic unit
- portable unit
- power feed unit
- power supply unit
- power train unit
- power unit
- power-generating unit
- power-tooling unit
- practical correction unit
- practical unit
- presetting unit
- pressurized air bearing unit
- primary storage unit
- probe unit
- processing unit
- production unit
- program unit
- programming unit
- propulsion unit
- pulling unit
- pump unit
- pumping unit
- pump-motor unit
- quill feed cam unit
- quill spindle unit
- quill unit
- raster unit
- readout unit
- reducing unit
- reduction gear unit
- reduction gearing unit
- reduction unit
- reed make contact unit
- regulating unit
- remote display unit
- replacement unit
- retriever unit
- right-angle milling unit
- right-angled milling unit
- robot power unit
- robot unit
- robot-transfer unit
- roller bearing unit
- roller unit
- roller-marking unit
- rotary unit
- rotating seal unit
- S unit
- scanning unit
- scheduling unit
- screen projection unit
- screwing unit
- sealed reed contact unit
- self-contained NC unit
- self-contained unit
- sensing unit
- sensor unit
- servo unit
- shankless boring unit
- sheet metal stamping automatic unit
- shop replaceable unit
- shuttle unit
- shuttle-and-lift unit
- side unit
- single-acting unit
- single-light unit
- single-reduction gear unit
- single-reduction unit
- sizing unit
- slant bed unit
- slave unit
- slide unit
- sliding table unit
- smallest replaceable unit
- spare unit
- speeder unit
- speed-increase unit
- speed-up spindle unit
- speed-up unit
- spindle box unit
- spindle cartridge unit
- spindle drive unit
- spindle unit
- stabilizing unit
- stand-alone unit
- standard build units
- starter auxiliary power unit
- static tooling unit
- steam generating unit
- stock feed unit
- storage unit
- stylus unit
- sub-multiple unit
- swing arm-mounted control unit
- tangent unit
- tapping unit
- teach control unit
- terminal control unit
- test unit
- testing unit
- thermal detecting unit
- tilting unit
- tolerance unit
- tool storage unit
- tool-presetting unit
- tool-spindle unit
- toroidal variable-speed friction drive unit
- track and store unit
- transfer unit
- transmission control unit
- transmission unit
- transmitter/receiver unit
- transport unit
- triple-reduction gear unit
- triple-reduction unit
- tuning unit
- turnaround unit
- turning spindle unit
- turnround unit
- turret unit
- twin gear unit
- twin saw unit
- twin-drive unit
- twin-screen unit
- unit of displacement
- unit of measure
- unit of measurement
- unit of physical quantity
- unit of product
- unit of work per unit of time
- unmanned machining unit
- vacuum unit
- variable coefficient unit
- variable delay unit
- variable preload bearing unit
- variable ratio unit
- variable speed unit
- variable-speed friction drive unit
- V-axis grinding unit
- V-belt variable-speed drive unit
- V-drive unit
- vertical way unit
- vibratory feed unit
- vise unit
- visual display unit
- vocal output unit
- VTL unit
- waveform gear reduction unit
- wheel-dressing unit
- wheel-head unit
- wing unit
- wing-base unit
- work storage unit
- work-holding headstock unit
- workshop video unit
- work-testing unit
- worm reduction unit
- writing unit
- yet-to-be-assembled unitEnglish-Russian dictionary of mechanical engineering and automation > unit
-
5 высота
altitude, height
(cm.pис.123)
- (астрономическая) — altitude (h)
in astronomy, angular displacement above the horizon.
- (габаритная) — height
- (над впп указываемая во взпетно-посадочных характеристиках) — height
- (поверхности или точки земли относительно уровня моря) — elevation the vertical distance of а point or а level on or affixed to the surface of the earth, measured from sea level.
- (полета) — altitude the elevation of an aircraft.
specified as above sl or above ground over which it flies.
-, абсолютная (полета ла) — true altitude
высота, изморенная от уровенной поверхности земного сфероида (ур.м.) до ла. — actual height above sea level, calibrated altitude corrected for air temperature.
-, абсолютная, барометрическая — true altitude
-, абсолютная критическая — critical altitude
- аэродрома (относительно уровня моря, над уровнем моря) — aerodrome elevation (-s.l.) the elevation of the highest point of the landing area.
-, аэродрома, барометрическая — aerodrome altitude
высота относительно уровня давления атмосферы (изобарической поверхности), устанавливаемого по шкале давления высотомера.
-, барометрическая — (pressure) altitude
атмосферное давление, выраженное в единицах высоты, соответствующей этому давлению (по мса). — the altitude corresponding to а given pressure in а standard atmosphere.
- барометрическая, (в метрах) — (... -meter) pressure equivalent altitude
-, безопасная, минимальная — minimum safe altitude (msa), safety height
высота, ниже которой не обеспечивается безопасность полета no приборам, ввиду напичия возвышенностей на пролeгаемой местности, — the altitude (height) below which it is hazardous to fly, in instrument flying conditions, owing to presence of high ground.
- безопасного полета над препятствиями, минимальная (рис. 112) — obstacle clearance limit (ocl)
- безопасного полета по приборам, минимальная — minimum instrument flight altitude
- бомбометания — bombing altitude
- в барокамере — pressure altitude
- верхней границы облаков — cloud-top height
- в зоне ожидания (посадки) — holding altitude
-, висения (вертолета) — hover(ing) height
высота, на которой вертолет не меняет своего положения в воздухе относительно к-п, объекта на поверхности под вертолетом. — а height at which the helicopter remains at а fixed роsition in the air with respect to some fixed object.
- в кабине, барометрическая — cabin pressure altitude
система кондиционирования воздуха самолета гражданcкoй авиации должна обеспечивать давление в кабинах, соответствующее высоте 8000 фт (2500 м) на максимальной высоте полета в нормальных условиях, — pressurized cabins and compartments to be occupied must be equipped to provide а cabin pressure altitude of not more than 8,000 feet at the maximum operating altitude of the airplane under normal operating conditions.
- в конце (2, 3) этапа (набора высоты при взлете) — height at end of (second, third) segment second segment-from the lg retraction complete to height of 400 m.
- в момент покидания самолета е парашютом — bailout /jump/ altitude
- всасывания — suction head
- выброски десанта — paradrop altitude
- (начала) выравнивания — flare(-out) altitude
- выравнивания (выхода в горизонтальный полет) — level-off altitude
высота, на которой самолет начинает переход между последним участком захода на посадку, после набора высоты, планирования или пикирования. — altitude at which an aircraft levels off after а climb, glide, or dive.
- выравнивания (перед посадкой) — flare-out height
высота между последним участком захода на посадку и горизонтальным выдерживанием до момента касания впп. — а height at which an airplane initiates transition between final approach and horizontal motion before touchdown.
-, габаритная — overall height
-, геометрическая — height
- головки зуба шестерни — addendum
-, заданная — desired /selected/ altitude
-, заданная, барометрическая — desired pressure altitude
altimeter reading + desired pressure altitude + corrections in ft. vs fl (flight level).
-, заданная по радиовысотомеру — preselected radio altitude height
- запуска всу (в полете) — apu inflight start altitude
- звезды — star altitude angle
-, зенитная — сo-altitude (ас)
угол между вертикалью и линией визирования на звезду. — со-altitude is the angle between vertical and line of sight to a star.
- измеряемая от уровня моря — altitude measured above sea level
-, исправленная (приборная) — calibrated altitude
-, истинная (полета над уровнем местности, над которой пролетает ла) — absolute altitude (above the flyover point) altitude above the actual surface, land or water.
-, кабинная поднимать кабинную в. до...м — cabin (pressure) altitude raise cabin altitude to...m
-, крейсерская — cruising altitude
- крейсерского полета — cruising altitude
постоянная (неизменяемая) высота полета на заданном участке маршрута, измеряемая от уровня моря, — а flight altitude, measured above sea level, proposed for that part of a flight from point to point during which a constant altitude will be maintained.
-, критическая — critical altitude critical aircraft altitude from 200 feet above runway.
- круга (над аэродромом) — (traffic) pattern altitude /height/
- круга (полета по кругу) — circuit flight altitude
-, максимальная рабочая (дв.) — critical altitude
- между вторым и третьим разворотом (при заходе на посадку) — downwind pattern altitude
- между первым и вторым разворотом — crosswind pattern altitude
- между третьим и четвертым разворотом — baseleg pattern altitude
- на маршруте, минимальная — minimum enroute altitude descend to mea if terrain clearance permits.
- над линией отсчета — height above reference zero
- над местностью (относительная) — height
- (полета) над местностью (геометрическая) — terrain clearance
- (полета) над местностью (недостаточная) с учетом конфигурации и скорости самолета — (insufficient) terrain clearance based on aircraft configuration and speed
- над поверхностью земли — height above ground surface
- над порогом впп — height above runway threshold
- над референц-аллипсоидом — height above reference ellipsoid
- над уровнем аэродрома (при взлете, наборе высоты) — height above takeoff surface
- над уровнем аэродрома (при заходе на посадку) — height above landing surface
- над уровнем моря — altitude above sea level
- начала выравнивания (перед приземлением) — flare-out altitude /height/
- начала уборки механизации — height at start of extendable high lift devices retraction
- начала уборки механизации и шасси — height at start of extendable devices retraction
- начала уборки шасси — height at start of landing gear retraction
- нижней кромки облачности (над уровнем земли или водной поверхности) — cloud ceiling height above the ground or water of the base of the lowest layer of cloud.
- ножки зуба шестерни — dedendum
-, нулевая — sea level altitude, zero altitude
высота на уровне моря или при полете в условиях стандартной плотности. — the altitude at sea level or flying in air that is equivalent to standard air density.
- облачности — cloud ceiling
- обледенения — icing altitude
- обязательного отключения автопилота — mandatory autopilot disconnect height
- окончания уборки закрылков, чистая — net height at end of flaps retraction
- окончания уборки механизации — height at end of extendable high lift devices retraction
- окончания уборки шасси, чистая — net height at end of landing gear full retraction
-, опасная (нопасн, задаваемая по радиовысотомеру) — alert altitude movable bug is installed on radio altimeter to set alert altitude.
-, — alt(itude) alert, alt alarm
-, опасная (сигнал) — altitude alert (signal)
-, остаточная (ност) высота начала отсчета высотомера. — residual altitude
- отключения автопилота (при заходе на посадку) — autopilot break-off /disconnect/ height
- откпючения системы управпения автоматическим заходом на посадку — auto-approach break-off height
-, относительная — height
расстояние по вертикали от ла до к-л. определенной уровенной поверхности на земле. — the vertical distance of an aircraft above a specified datum.
-, относительная (относительно уровня аэродрома вылета или посадки) — height (above takeoff or landing surface)
- относительно начала координат (чистая) — (net) height above reference zero
-, относительная барометрическая, высота по давлению у земли (на уровне аэродрома), выставляемая на высотомере перед посадкой — qfe altitude (fe - field elevation) altitude setting to read zero when touched down. atmospheric pressure at aerodrome elevation (or at runway threshold).
- перевода шкалы давления высотомера — transition altitude
- пересечения входной кромки впп — (runway) threshold crossing height
- перехода — transition altitude
высота, при которой производится установка шкалы давления высотомера на давление 1013 мб (760 мм рт.ст) после набора высоты. — when passing the transition altitude set the altimeter to 1013mb,during climb.
- перехода к (напр. посадочной) конфигурации — altitude for transition to (landing) configuration
- — horizontally-sustained step altitude
- площадки (посадочной или взлетной, учитываемая при определении веса ла) — field altitude
- площадки, барометричеcкая (взлетно-посадочной) — (air) field altitude
- по атмосферному давлению, приведенному к уровню моря (при установке шкалы давления высотомера) — qnh altitude nh-natural height altimeter sub-scale setting to obtain elevation when on the ground.
- no давлению у земли (на уровне аэродрома), выставляемая на высотомере перед посадкой — qfe altitude atmospheric pressure at aerodrome elevation (or at runway threshold)
- по плотности (воздуха) — density altitude
when runway length is marginal, or when landing at altitude, compute density altitude.
- no показанию высотомера при установке барометрической шкалы на стандартное (атмосферное) давление — qne altitude ndicated height on landing with altimeter sub-scale set to 1013.2 mb (760 mm hg).
- по радиовысотомеру — radio (altimeter) altitude /height/
- по стандартному атмосферному давлению — qne altitude
- повторного запуска (двигателя в воздухе) — ге-starting altitude, inflight start altitude
- подсоса (насоса) — suction head
- подхода к цепи — height of target approach
- подъема клапана — valve travel
- полета — flight altitude
расстояние по вертикали от уровня, принятого за нуль отсчета, до летательного annapaтa. — а vertical distance from the reference zero level to the aircraft in the air.
- полета на уровне моря — sea level flight altitude
- полета, неизменяемая — constant (flight) altitude
- полета no кругу (над аэродpoмoм) — circuit flight altitude /height/
- полета, постоянная — constant altitude
при крейсерском полете выдерживается постоянная высота. — during а cruising flight the altitude is maintained constant.
-, полная — gross height
геометрическая высота в каждой точке траектории взлета при условии полного градиента набора высоты. — the geometric height attained at any point in takeoff flight path using gross climb performance.
- порога аварийного выхода над полом кабины (не боnee чем...mm) (рис. 102) — emergency exit step-up inside the airplane (of not more than...mm)
- порога аварийного выхода над крылом (рис. 102) — emergency exit step-down outside the airplane
- порога аварийного выхода от земли — emergency exit step-down height (outside the aircraft)
- порога двери (после аварийной посадки с убранной передней опорой) — door sill height (with nose gear collapsed)
- порога двери (после аварийной посадки с убранными шасси) — door sill height (with all gear collapsed)
- порога двери (при нормальном положении ла) — door sill height (in normal altitude)
- предстоящего полета — expected altitude
- преодоления препятствия (hnpen) (рис. 112) — obstacle clearance limit (ocl)
- препятствия (нпреп) (рис. 112) — obstacle height
- при взлете (до высоты 400 м) — takeoff height
- приборная, исправленная — calibrated altitude
- принятия решения, минимапьная (нреш) — decision height (dh), minimum decision altitude (mda)
наименьшая высота, на котарой должно быть принято решение: или продолжать заход на посадку, или начинать маневр ухода на второй круг. — "decision height", with геspect to the operation of aircraft, means the height at which а decision must be made, during an ils or par instrument approach, to either continue the approach or to execute a missed approach.
- принятия решения ухода на второй круг — go-around decision height
- при работе двигателей с впрыском воды, максимальная (при взлете) или на форсажном режиме — maximum wet thrust height
- пропета над местностью — terrain altitude
- пропета над препятствием — obstacle clearance
- пролета над препятствиями в секторе глиссады, безопасная — glide path sector obstacle clearance
- пропета над препятствиями, минимальная — obstacle clearance limit (ocl)
- пролета ппм — waypoint passing altitude
- пролета радиомаркера — marker passing /crossing/ height
-, рабочая — operating altitude
- разгона до околозвуковой скорости — transonic acceleration altitude
- расположения аэродрома (истинная над уровнем моря) — aerodrome elevation
- расположения аэродрома (на графиках рлэ) — aerodrome altitude fig. 1 gives т.о. weight for aerodrome altitude and temperature.
-, расчетная — rated altitude
- решения, заданная по радиовысотомеру — preselected radio altitude decision height
- самолета на стоянке — airplane (overall) height at rest
- сброса (грузов, десанта) — paradrop altitude
- сброса шасси (при копровых испытаниях) — landing gear drop height
- светила — celestial body altitude angle
угол между плоскостью истинного горизонта и напрявлением на светило. высота светила измеряется дугой вертикали светила от истинного горизонта до места светипа в пределах от о до +90 (положительное значение к зениту от горизонта, отрицательное - к надиру). — angular displacement above the horizon, the area of a vertical circle between the horizon and a point on the celestial sphere, measured upward from the horizon.
- свободного сброса шасси (при копровых испытаниях) — landing gear free drop height
- срабатывания (к-л. устройства, срабатывающего при достижении определенной высоты) — response altitude
- срабатывания взрывателя — fuzing altitude
- средняя — mean height
-, текущая — present altitude
- уборки механизации (и шасси) — extendable devices retraction height
- условного препятствия (при взлете, посадке) — screen height
- установившегося полета — sustained altitude
- установки шкалы давления высотомера (высота перехода) — transition altitude
- установки высотомера на к-л. заданную высоту — altimeter setting altitude
- установки подвижного индекса высотомера на заданную высоту (напр. высоту принятия решения) — altimeter setting altitude when the aircraft passes through the altitude setting of the radio altimeter mda bug, a minimus voice alert is given.
- ухода на второй круг — missed-approach altitude /height/
минимальная высота, на которой должен быть начат маневр ухода на второй круг, — missed-approach altitude is the minimum height аt which final approach should be discontinued if it cannot be completed.
-, чистая — net height
геометрическая высота в лю6ой точке траектории взлета при соблюдении условий чистого набора высоты, — the geometric height attained at any point in the takeoff flight path using net climb performance.
-, чистая, относительная — net height
- щетки (электрической машины) — brush length
- эшелона (нэш) — flight level
отсчитывается от условного уровня, кот. соответствует стандарт. атмосф. давлению 760 мм рт. ст. — measured above the referепсе datum corresponding to atmospheric pressure of 760 mm hg.
- эшелона, заданная — preset flight level
- эшелона перехода — transition level
высота, при которой шкала давления высотомера устанавливается с давления 1013 мб (760 мм рт.ст.) на давление на уровне аэродрома, при заходе на посадку. — at the transition level the pilot sets the altimeter to actual qnh. the change in altimeter setting from 1013 mb to local qnh can be made when an approach clearance is issued.
диапазон в. — altitude range
потеря в. — loss of altitude
на всех в. — at any (appropriate) altitude
с набором в. — in climb
с потерей в. — in descent
с увеличением (уменьшением) в. — with increase (decrease) in altitude
висеть на в.... метров от земли — hover at а height of... meters from the ground
выдерживать в. — maintain altitude
занимать (заданную) в. — reach (pre-selected) altitude
лететь над в. перехода — fly above transition altitude
лететь ниже опасной в. — fly below minimum safe altitude /height/, fly at unsafe altitude
набирать в. — climb
поднимать в. в кабине до... м — raise cabin altitude to... m
регулировать no в. (сиденье летчика) — adjust for height
сообщать о достижении в.... метров — report reaching... meters
сообщать об уходе (снижении) с в.... метров — report leaving meters
терять в. — lose altitude, descend
увеличивать в. — increase altitude, climbРусско-английский сборник авиационно-технических терминов > высота
См. также в других словарях:
Miniature valve — The miniature thermionic valve (vacuum/electron tube) is a development of the older style of thermionic valve in which the pins for connecting the valve to circuitry were mounted in a Bakelite base, into which the valve envelope ( bulb ) was… … Wikipedia
Call of Duty: Modern Warfare 2 — Разработчик Infinity Ward … Википедия
List of oil field acronyms — Contents 1 # 2 A 3 B 4 C … Wikipedia
HMS Affray (P421) — HMS Affray (P421), a British Amphion class submarine was the last Royal Navy submarine to be lost at sea, on 16 April 1951, with the loss of 75 lives. All vessels of her class were given names beginning with the letter A; she was the only ship of … Wikipedia
Submarine — For other uses, see Submarine (disambiguation). A Japan Maritime Self Defense Force Oyashio class submarine in 2006 A submarine is a watercraft capable of independent operation below the surface of the water. It differs from a submersible, which… … Wikipedia
Chevrolet Vega — 1972 Chevrolet Vega GT Hatchback Coupe Manufacturer Chevrolet Division of General Motors Also called Vega 2300 … Wikipedia
Electronic amplifier — A practical amplifier circuit An electronic amplifier is a device for increasing the power of a signal. It does this by taking energy from a power supply and controlling the output to match the input signal shape but with a larger amplitude. In… … Wikipedia
Ford Torino — Infobox Automobile name=Ford Torino 1970 Ford Torino Cobra SportsRoof manufacturer=Ford Motor Company production=1968 ndash;1976 class=Intermediate layout= FR layout assembly=Atlanta, Georgia Lorain, Ohio Chicago, Illinois predecessor=Ford… … Wikipedia
Dota (genre) — For other uses, see DOTA (disambiguation) … Wikipedia
Health and Disease — ▪ 2009 Introduction Food and Drug Safety. In 2008 the contamination of infant formula and related dairy products with melamine in China led to widespread health problems in children, including urinary problems and possible renal tube… … Universalium
Business and Industry Review — ▪ 1999 Introduction Overview Annual Average Rates of Growth of Manufacturing Output, 1980 97, Table Pattern of Output, 1994 97, Table Index Numbers of Production, Employment, and Productivity in Manufacturing Industries, Table (For Annual… … Universalium